Clavia Nord C2 Manual de usuario descargar pdf (Pagina 20)

About the MIDI implementation

The following MIDI messages can be transmitted and received from the

Nord C2:

Note On/Off

• Note On and Note Off messages are transmitted and received.

Controllers

In the MIDI Menu (see page 18), you can select if the Nord C2 should

transmit and/or receive Control Change messages.

• If you have a control pedal connected to the Swell pedal input, this is

transmitted as Controller 4 (Swell).

• If you have a pedal connected to the sustain pedal input, this is

transmitted as Controller 64 (Sustain Pedal).

• If you have a pedal connected to the rotor pedal input, this pedal is

transmitted as Controller 82.

• Almost all other controls (knobs and buttons) on the front panel are

also transmitted (and received) as Control Change messages. This

can be used to record your actions on the front panel into a MIDI

sequencer. For a full list of which parameters correspond to the Con-

troller numbers, see the MIDI implementation on the next page.

Keyboard velocity

The Nord C2 can transmit and receive keyboard velocity messages.

Organ sounds will always be played back at nominal level regardless of

incoming MIDI Velocity data. Release velocity is also transmitted.

Program change

In the MIDI Menu (see page 17), you can select if the Nord C2 should

send and/or receive Program Change messages.

When you select a Program, a Program Change message is transmit-

ted via MIDI. If a Program Change message is received on the selected

MIDI Channel, the Nord C2 will change Program accordingly.

The 128 Program locations (programs 1-126 + Live 1 and Live 2) send

and respond to MIDI Program Change values 0-127.

MIDI Sysex (System Exclusive)

Individual Programs or all Programs can be transmitted and received as

a System Exclusive dump.

Nord C2 with a sequencer

Connections

1 Connect the MIDI Out on the Nord C2 to the MIDI In on your

sequencer.

2 Connect the MIDI Out from your sequencer to the MIDI In on the

Nord C2.

Local On/Off

Local Off may be used when you use a sequencer to record and play

back from Nord C2. If the sequencer echoes back incoming MIDI data,

the Nord C2 may respond twice to every note and other message/ac-

tion if e.g. the keyboard and the sequencer sends the same MIDI infor-

mation to the unit. Local On/Off is set on the “MIDI menu” see page 17.

MIDI Channel

The MIDI channel(s) that the Nord C2 uses are set up in the MIDI menu

- see “MIDI menu” on page 17.

Program Change

Usually you select a Program Change value for a track in the sequenc-

er track settings. The 128 program locations send and respond to

Program Change values 0-127.

If you want to record a Program Change message, activate recording

in the sequencer and simply select the program on the Nord C2.

Controllers

When you record actions with knobs and buttons, make sure that the

sequencer “echoes” the changes back on the correct MIDI Channel, or

your changes won’t have any effect.

Some notes about controllers and “chasing”

Consider a situation where you record a Controller message, e.g. a

Drawbar opening, in the middle of your sequencer song. Then you “re-

wind” the sequencer to a position before the recorded Drawbar open-

ing. The problem is that the Nord C2’s Drawbar will remain opened,

although it really should be as it was before you recorded the opening.

To solve this, you could record a “snapshot” of all Controller settings

of the Nord C2 Program at the beginning of your sequencer song. See

“Sending MIDI Controller dumps” below.

MIDI functions

20 | Nord C2 Combo orgaN User maNUal os v2.X

1 2 ... 15 16 17 18 19 20 21 22 23 24 25

Comentarios a estos manuales

Sin comentarios

Clavia Nord C2 Manual de usuario Pagina 20

Comentarios a estos manuales